Do you need custom fasteners created with Alloy 20? Since our inception, Vegas Fastener Group has met every challenge of providing Quality, Timely, Cost-effective solutions for specialty fastener applications. Every product is built to your specifications, using your prints if necessary.
Below are the technical specifications of the Alloy 20 Bar Stock we have available to meet your needs.
Alloy 20-245 Precious Metal Alloy
Subcategory: Metal; Nonferrous Metal Material Notes: All values may vary dependant on specific design and usage
Proprietary composition Capabilities:
Information provided by California Fine Wire.
| Physical Properties |
Metric |
English |
Comments |
| Density |
11.5 g/cc |
0.414 lb/in³ |
|
| Mechanical Properties |
| Tensile Strength @ Break |
765 MPa |
111000 psi |
Stress relieved |
| Tensile Strength @ Break |
862 MPa |
125000 psi |
Hard |
| Modulus of Elasticity |
63.8 GPa |
9250 ksi |
|
| Electrical Properties |
| Electrical Resistivity |
4.07e-005 ohm-cm |
4.07e-005 ohm-cm |
3% tolerance on sizes below 0.02, 5% tolerance on sizes above 0.02 |
| Descriptive Properties |
| Magnetic |
None |
|
| Temperature Coefficient of Resistance |
Max 0.00002 ohms/ohm-°C |
0-100°C |
| Thermal EMF vs Copper |
-0.041 mV |
|
Do you need custom fasteners created with AL6XN? Since our inception, Vegas Fastener Group has met every challenge of providing Quality, Timely, Cost-effective solutions for specialty fastener applications. Every product is built to your specifications, using your prints if necessary.
Below are the technical specifications of the AL6XN Bar Stock we have available to meet your needs.
AL6XN
Subcategory: The physical properties of the AL-6XN alloy are similar to those of other austenitic stainless steels Uses for AL6XNOriginally developed for seawater applications, the AL-6XN alloy is used successfully in food, pharmaceutical, and biopharmaceutical services. The “superalloy” is resistant to attack by corrosive food and beverage products such as: sports drinks, ketchups, soy and barbecue sauces, and salsas.
It is also successful with fine chemical, cosmetic and pharmaceutical (cosmeceutical), bulk pharmaceutical, brewery, desalination, semi-conductor, aerospace, biopharm, pulp and paper, and gas handling applications.
| Component |
Wt. % |
| Chromium |
20% |
| Nickel |
24% |
| Molybdenum |
6.3% |
| Nitrogen |
36 |
| Mn |
.22% |
| Copper |
.25% – .75% |
| PREN |
44.3 |
Material Notes: AL-6XN alloy is metallurgically stable to 1000° F (540° C) and has no phase transformation even after extensive deformation. When exposed to temperatures in the range of 1200-1800° F the opportunity for chi phase formations exists. Chi phase, a chromium-iron-molybdenum compound which is sometimes incorrectly referred to as sigma phase, forms along the grain boundaries depleting the area of molybdenum and chromium reducing the corrosion resistance of the material. In order to help combat chi phase formation, nitrogen was added to the AL-6XN alloy to minimize this formation improving corrosion resistance and increasing strength over a broad range of temperatures, while maintaining the good formability of austenitic stainless steel.
| Physical Properties |
Value |
Units |
Comments |
| Density |
0.291
8.06 |
lb/in3 g/cm3 |
|
| Mechanical Properties |
| Modulus of Elasticity |
28.3 x 106195 |
psiGPa |
|
| Melting Range |
2410 to 2550 |
ºF |
|
Coefficient of Expansion
68 to 212 °F
20 to 100 °C |
8.5
15.3 |
10-6/ °F
10-6/ °C |
|
| Modulus of Elasticity |
193 GPa |
28000 ksi |
In Tension |
| Sealing Temperature |
1885
1030 |
°F
°C |
|
| Electrical Properties |
| Electrical Resistivity |
535
0.89 |
Ohm·circ mil/ft
µOm |
|
| Magnetic Permeability |
1.0028
1.0028 |
Oersted
(µ at 200H) |
Fully annealed 0.5″ plate 65% cold-worked plate |
| Thermal Properties |
| Specific Heat Capacity |
0.11
500 |
Btu/lb·°F
J/kg·K |
|
Do you need custom fasteners or bolts created with A286? Since our inception, Vegas Fastener Group has met every challenge of providing quality, timely, cost-effective solutions for A286 fastener and A286 bolt applications. Every A286 product is built to your specifications, using your prints if necessary.
Below are the material properties and technical specifications of the A286 bar stock we have available to meet your needs.
Special Metals INCO® A286 Iron-Nickel-Chromium Alloy
Subcategory: Iron Base; Metal; Superalloy
| Component |
Wt. % |
| Al |
Max 0.35 |
| B |
0.001 – 0.01 |
| C |
Max 0.08 |
| Cr |
13.5 – 16 |
| Fe |
60 |
| Mn |
Max 2 |
| Mo |
1 – 1.5 |
| Ni |
24 – 27 |
| S |
Max 0.03 |
| Ti |
1.9 – 2.35 |
| V |
0.1 – 0.5 |
| W |
3 -4.5 |
Material Notes: Iron content calculated as remainder.
Data provided by the manufacturer, Special Metals.
| Physical Properties |
Metric |
English |
Comments |
| Density |
7.94 g/cc |
0.287 lb/in³ |
|
| Mechanical Properties |
| Modulus of Elasticity |
201 GPa |
29200 ksi |
|
| Electrical Properties |
| Electrical Resistivity |
9.1e-005 ohm-cm |
9.1e-005 ohm-cm |
|
| Magnetic Permeability |
1.007 |
1.007 |
at 200 Oersted (15.9 kA/m) |
| Thermal Properties |
| CTE, linear 20°C |
16.4 µm/m-°C |
9.11 µin/in-°F |
Mean 27-100°C |
| CTE, linear 250°C |
16.9 µm/m-°C |
9.39 µin/in-°F |
Mean 27-300°C |
| CTE, linear 500°C |
17.5 µm/m-°C |
9.72 µin/in-°F |
Mean 27-500°C |
| CTE, linear 1000°C |
17.7 µm/m-°C |
9.83 µin/in-°F |
Mean 27-700°C |
| Heat Capacity |
0.419 J/g-°C |
0.1 BTU/lb-°F |
|
| Thermal Conductivity |
12.7 W/m-K |
88.1 BTU-in/hr-ft²-°F |
|
| Melting Point |
1370 – 1430 °C |
2500 – 2610 °F |
|
| Solidus |
1370 °C |
2500 °F |
|
| Liquidus |
1430 °C |
2610 °F |
|
| Maximum Service Temperature, Air |
700 °C |
1290 °F |
good strength and oxidation resistance |
Do you need custom fasteners created with 904L? Since our inception, Vegas Fastener Group has met every challenge of providing Quality, Timely, Cost-effective solutions for specialty fastener applications. Every product is built to your specifications, using your prints if necessary.
Below are the technical specifications of the 904L Bar Stock we have available to meet your needs.
Allegheny Ludlum Stainless Steel AL 904L™ Alloy (UNS N08904)
Subcategory: Metal; Stainless Steel; T 400 Series Stainless Steel Key Words: DIN 1.4539; ASTM B-625; ASME SB-625
| Component |
Wt. % |
| C |
Max 0.02 |
| Cr |
19 – 23 |
| Cu |
1 – 2 |
| Fe |
47 |
| Mn |
Max 2 |
| Mo |
4 – 5 |
| Ni |
23 – 28 |
| P |
Max 0.045 |
| S |
Max 0.035 |
| Si |
Max 1 |
Material Notes: Iron content above calculated as balance.
Allegheny Ludlum AL 904 L™ Alloy (UNS N08904) is an austenitic stainless steel alloy designed for a middles to high level of corrosion resistance. The alloy is produced to low carbon levels for use in the welded condition as in welded vessels and other large and complex fabrications.
The high nickel (25%) and molybdenum (4.5%) contents of the AL 904L alloy provide good resistance to chloride stress corrosion cracking, although not total resistance as judged by the extremely severe laboratory test, boiling magnesium chloride.
The N08904 alloy has been incorporated in ASTM and ASME specifications, and is widely and readily available in a variety of product forms, welding electrodes, and fittings. The AL 904L Alloy has performed well in a variety of service environments such as utility scrubbers, acid and fertilizer production.
Information provided by Allegheny Ludlum Corporation.
| Physical Properties |
Metric |
English |
| Density |
7.9 g/cc |
0.285 lb/in³ |
|
| Mechanical Properties |
| Hardness, Brinell |
150 |
150 |
Typical |
| Hardness, Rockwell B |
70 – 90 |
70 – 90 |
79 IsTypical |
| Tensile Strength, Ultimate |
Min 490 MPa |
Min 71100 psi |
605 MPa Typical; 490 MPa min. |
| Tensile Strength, Yield |
Min 220 MPa |
Min 31900 psi |
270 MPa Typical; 220 MPa min. |
| Elongation at Break |
Min 36 % |
Min 36 % |
50% Typical; 36% min. |
| Reduction of Area |
55 % |
55 % |
|
| Modulus of Elasticity |
190 GPa |
27600 ksi |
|
| Electrical Properties |
| Electrical Resistivity |
9.52e-005 ohm-cm |
9.52e-005 ohm-cm |
|
| Magnetic Permeability |
Max 1.02 |
Max 1.02 |
|
| Thermal Properties |
| CTE, linear 20°C |
15.3 µm/m-°C |
8.5 µin/in-°F |
Range 20° – 100°C |
| CTE, linear 500°C |
16.5 µm/m-°C |
9.17 µin/in-°F |
Range 20° – 400°C; 18.2 µm/m-°C Range 20°- 800°C |
| Thermal Conductivity |
11.5 W/m-K |
79.8 BTU-in/hr-ft²-°F |
at 20°C; 12.9 W/M-°K at 100°C |
